引用本文:
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  【EndNote】   【RefMan】   【BibTex】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 921次   下载 300 本文二维码信息
码上扫一扫!
分享到: 微信 更多
飞机发动机叶片激光熔覆性能
徐国建, 郭云强, 李春光, 唱丽丽, 邱晓杰1,2,3,4
1. 沈阳工业大学 材料与工程学院, 沈阳 110870;2.
2. 朗星无人机系统有限公司, 成都 610200;3.
3. 辽宁增材制造产业技术研究院, 沈阳 110021;4.
4. 沈阳中科煜宸科技有限公司, 沈阳 110021
摘要:
为了修复飞机发动机叶片(K417G)的铸造缺陷和损伤,采用了500W-IPG光纤激光熔覆系统将镍基合金粉末(RCF-201)熔覆到镍基高温合金K417G基体上.利用显微镜、扫描电子显微镜(SEM)、X射线衍射(XRD)、电子探针(EPMA)和能谱仪(EDS)等分析了堆焊层的组织和成分,用显微硬度计分析了堆焊层硬度分布,用高温蠕变实验机分析了堆焊层高温蠕变性能.试验结果表明,熔覆层从熔合线到表面的组织依次由平面晶、柱状晶和等轴晶组成;熔覆层的组织为亚共晶组织,初晶相为富镍固溶体γ-Ni,共晶组织为γ-Ni+Cr7C3+Cr23C6+(Mo0.54,Ti0.46) C;熔覆层的硬度约为650 HV,约是母材硬度(350 HV)的1.86倍;在950℃/235 MPa条件下,激光熔敷试样的蠕变寿命最长约为26.17 h,且断裂位置位于母材.
关键词:  激光熔敷  高温合金K417G  亚共晶组织  初晶相  蠕变寿命
DOI:10.12073/j.hjxb.2018390204
分类号:TG456.7
基金项目:
Resaerch of laser cladding performance of engine blades
XU Guojian, GUO Yunqiang, LI Chunguang, CHANG Lili, QIU Xiaojie1,2,3,4
1. School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110870, China;2.
2. Star-UAV System., Ltd., Chengdu 610200, China;3.
3. Institute of Liaoning Additive Manufacturing Technology Industry, Shenyang 110021, China;4.
4. Shenyang Zhongke Raycgam Science and Technology Co., Ltd., Shenyang 110021, China
Abstract:
In order to repair aircraft engine blades (K417G) of the casting defects and damage. Ni-based alloy powder (RCF-201) was cladded on a nickel-based superalloy K417G substrate by a 500W-IPG fiber laser cladding system. The microstructure and composition of the surfacing layer were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), electron probe microanalysis (EPMA) and energy dispersive spectrometer (EDS), the hardness distribution of surfacing layer was analyzed by microhardness tester, the creep properties of surfacing layer was analyzed by high temperature creep testing machine. The results show that, the microstructure of the cladding layer from the fusion line to the surface consists of plane crystal, columnar crystal and equiaxed crystal; The microstructure of the cladding layer is hypoeutectic structure, the primary crystal phase is Ni-rich solid solution and the eutectic structure is γ-Ni + Cr7C3 + Cr23C6 + (Mo0.54, Ti0.46) C; The hardness of the cladding layer is about 650 HV, which is about 1.86 times the hardness of the base metal (350 HV); Under the condition of 950℃/235 MPa, the creep life of laser cladding specimen is about 26.17 h and the fracture position is located at the base metal.
Key words:  laser cladding  superalloy K417G  hypoeutectic structure  primary phase  creep life